The advantages of the optical fiber laser cutting machine are mainly reflected in that it will not produce deformation, high flexibility, small slits, smooth section without burrs, and can cut any complex graphic workpiece. So, how to buy a fiber laser cutting machine with high cost performance? You can start from the following aspects:
1. The range of materials and business needs processed by the enterprise
We need to consider the factors such as the scope of our business, the thickness of cutting materials, and the materials we need to cut, and then the power of the equipment we need to buy and the size of the worktable. At present, the power of the laser cutting machine on the market is between 500W-6000W, and the size of the worktable can be customized according to the needs of customers.
2. Laser power
When selecting the performance of the laser cutting machine, we should consider our own environment. The size of the laser power is very important. For example, we often cut the metal sheet below 6mm, so we can choose the 500W-700W laser cutting machine to meet the production demand. If we cut the material above 6mm, we need to consider the machine with higher power, which is very helpful for the cost control of enterprises.
3. Part of laser cutting machine
We also need to pay attention to some important parts of the laser cutting machine. The laser generator, laser cutting head, servo motor, guide rail, water tank, etc. should be clearly identified as domestic or foreign. These components directly affect the cutting speed and accuracy of the laser cutting machine.

For beginners, when they encounter poor cutting quality, they will make difficulties and do not know how to adjust many parameters. The following is a brief introduction to the problems and solutions.

Parameters affecting cutting quality include cutting height, cutting nozzle model, focus position, cutting power, cutting frequency, cutting duty ratio, cutting air pressure and cutting speed. Hardware conditions include: protective lens, gas purity, plate quality, focusing lens and collimating lens.

How to adjust the parameters of laser cutting machine?

In case of poor cutting quality, it is recommended to carry out general inspection first. The main inspection contents and sequence of general inspection are:

1. The cutting height (the actual cutting height is recommended to be between 0.8~1.2mm). If the actual cutting height is not accurate, it needs to be calibrated.

2. Check whether the cutting nozzle model and size are wrong. If it is correct, check whether the cutting nozzle is damaged.

3. It is recommended to use the cutting nozzle with diameter of 1.0 to check the optical center, and the focus is between - 1 and 1 when checking the optical center. The light point is small and easy to observe.

4. Protective lens Check whether the protective lens is clean and free of water, oil and slag. Sometimes the protective lens will be fogged due to the weather or too cold paving air.

5. Focus Check whether the focus is set correctly. If it is an autofocus cutting head, you must use the mobile phone APP to check whether the focus is correct.

6. Modify cutting parameters

After checking the above items and finding no problems, modify the parameters according to the phenomenon.

How to adjust the parameters according to the phenomenon? The following is a brief introduction to the conditions and solutions encountered when cutting stainless steel and carbon steel.

For example, there are many types of stainless steel slag. If only corner slags are hung, the corner rounding can be considered first. In terms of parameters, the focus can be reduced and the air pressure can be increased.

If hard slag is hung on the whole, it is necessary to reduce the focus, increase the air pressure and increase the cutting nozzle, but too low focus or too high air pressure will lead to section delamination and surface roughness. If granular soft slag is hung on the whole, the cutting speed can be appropriately increased or the cutting power can be reduced.

When cutting stainless steel, you may also encounter slag hanging on the side near the end of cutting. You can check whether the gas supply is insufficient and the gas flow cannot keep up.

Cutting carbon steel will generally meet the following problems: the thin plate section is not bright enough, and the thick plate section is rough.

Generally speaking, 1000W laser can cut carbon steel no more than 4mm bright, 2000W is 6mm, 3000W is 8mm.

If you want to cut the section bright, first of all, the surface of the plate must be free of rust, paint and oxide skin, and then the oxygen purity must be at least 99.5% higher. In cutting, you need to pay attention to the following: use a small cutting nozzle with double layers of 1.0 or 1.2, the cutting speed needs to exceed 2m/min, and the cutting pressure should not be too high.

If you want the quality of the thick plate cutting section to be good, you must first ensure the purity of the plate and gas, and then select the cutting nozzle. The larger the hole diameter, the better the section quality will be, but at the same time, the greater the section taper will be